ANALISIS PENGENDALIAN KUALITAS PRODUK BAJA TULANGAN SIRIP S36 DENGAN MENGGUNAKAN METODE TAGUCHI PADA QUALITY CONTROL

  • Fransisco Toebagoes Dias Permana UNIVERSITAS BANTEN JAYA
  • Sri Mukti Wirawati UNIVERSITAS BANTEN JAYA
  • Anita Dyah Juniarti UNIVERSITAS BANTEN JAYA
Keywords: Methode Taguchi, Optimal, Partameter

Abstract

PT. Krakatau Osaka Steel is a company engaged in the manufacturing industry which produces Reinforcement Bar, for the product under study, namely S36, which experienced an increase in product defects with dimensions that did not meet standards. The aim of this research is to determine optimal parameters to reduce product defects in S36 products. This research was conducted using the Taguchi method. The Taguchi method can be used in companies to evaluate a process or product that is not yet efficient so that a process or the results of the product produced can be maximized. The setting parameters used are rolling speed (s) and raw material heating time (s), the standards of which have not yet been determined. Data was collected by conducting parameter experiments and analyzed using Minitab 20 software. Based on the research results, it can be concluded that the most influential parameter is rolling speed and the optimal parameter for defective product results with the largest S/N Ratio value is at level 2 for rolling speed. namely -1.915 with a speed of 50 seconds and level 3 for heating time, namely -2.401 with a heating time of 3000 seconds. So, the optimal improvement proposal is to set parameters of 50 seconds for rolling speed and 3000 seconds for heating time.

References

Alfarabi, K. M. (2022). Pengaruh Mass Customization, Kualitas Produk dan Harga terhadap Kepuasan Konsumen (Studi Usaha Sofa KMJ Jl. Pattimura Kota Jambi) (Doctoral dissertation, Universitas Jambi).

Bagchi. (2013). Taguchi Methods Explained Practical Steps to Robust Degin. New Delhi: Published by Prentice – Hall of India Private Limited, M-97, Connaught Circus, and Printed by Bhuvnesh Seth at Rajkamal Electric Press, B-35/9, G.T. Karnal Road Industrial Area, Delhi 11003.

BSN (2017). Baja tulangan beton SNI 2052:2017. Jakarta, Indonesia.

Gaspersz , Vincet. (2001). Total Quality Manajement. Jakarta PT. Gramedia Pustaka Utama.

Hardana, A., Nasution, J., & Damisa, A. (2022). Analisis Pengaruh Kualitas Produk dan Kualitas Pelayanan terhadap Minat Nasabah Menabung pada PT. BSI Cabang Padangsidimpuan. Jurnal Masharif Al-Syariah: Jurnal Ekonomi dan Perbankan Syariah, 7(2), 828-838.

Montgomery, Douglas C., (2001). Introduction to Statistical Quality Control, 4 th Edition. John Wiley & Sons, Inc., New York.

Muharom dan Siswadi. (2015). Desain Eksperimen Taguchi untuk Meningkatkan Kualitas Batu Bata Berbahan Baku Tanah Liat. Jemis Vol. 3 No. 1 Tahun 2015.

Revita, I., Suharto, A., & Izzudin, A. (2021). Studi Empiris Pengendalian Kualitas Produk pada Vieyuri Konveksi. Bisnis-Net Jurnal Ekonomi Dan Bisnis, 4(2), 39-49.

Soejanto, Irwan. (2009). Desain Experimen Metode Taguci. Surabaya : Graha Ilmu

Sofjan Assauri (2008). Manajemen Produksi dan Operasi. Jakarta: LPFE UI, 299.

Susanti, E., Indrawati, I., Dwipurwani, O., Sitepu, R., & Cahyawati, D. (2020). Pengenalan Software Minitab Kepada Guru-Guru di Wilayah Gugus II Indralaya Kabupaten Ogan Ilir Sumatera Selatan. Jurnal Pemberdayaan: Publikasi Hasil Pengabdian Kepada Masyarakat, 4(3), 267-274.
Published
2024-06-30
How to Cite
Permana, F., Wirawati, S., & Juniarti, A. (2024). ANALISIS PENGENDALIAN KUALITAS PRODUK BAJA TULANGAN SIRIP S36 DENGAN MENGGUNAKAN METODE TAGUCHI PADA QUALITY CONTROL. Jurnal Intent: Jurnal Industri Dan Teknologi Terpadu, 7(1), 1-10. Retrieved from https://ejournal.lppm-unbaja.ac.id/index.php/intent/article/view/3403
Section
Articles

Most read articles by the same author(s)

1 2 3 > >>