ANALISIS PENGENDALIAN KUALITAS CACAT DIMENSI PADA HEADER BOILER MENGGUNAKAN METODE FMEA DAN FTA DI PT. IHI POWER SERVICE INDONESIA (IPSI)
Abstract
IHI Power Service Indonesia is a company engaged in the Boiler Pressure Part Industry (Fabrication) in every production activity it always strives to produce quality products according to ASME standards (American Society of Mechanical Engineers). Production results are less than the maximum. In the 2020 period the total production was 28,527 tons and the number of defects was 364 tons, in the 2021 period the total production was 22,703 tons and the number of defects was 301 tons. The author uses the Failure Mode And Effect Analysis (FMEA) method and the Failure Tree Analysis (FTA) method. From the results of data processing using a Pareto diagram based on the RPN value obtained from the FMEA method, the dominant type of defect is obtained, namely Hole Distance with an RPN value of 364.5 and Dimension Length with a value of 351.17, then analyzed using FTA, at the proposed improvement stage it is proposed to use the 5W+1H method. Factors that cause defects include inaccurate and faded measuring instruments, rare maintenance on radial drilling machines and blades that are rarely replaced. Proposed improvements to reduce defects include requesting replacement of measuring instruments, carrying out regular maintenance of radial drilling drilling machines, holding shift schedules for operators, conducting training for operators.
References
Al-Faritsy, A. Z., & Kalid, S. I. (2021). Pengendalian Produk Tas Kulit Menggunakan Metode Six Sigma dan 5W1H. Jurnal Teknik, 8(1). https://doi.org/10.31000/jt.v8i1.1595.
Alkatiri, H. A., Adianto, H., & Novirani, D. (2015). Implemetasi Pengendalian Kualitas untuk Mengurangi Jumlah Produk Cacat Tekstil Kain Katun Menggunakan Metode Six Sigma pada PT. SSP. Jurnal Online Institut Teknologi Nasional, Vol 03(03), 148-159.
Ardyansyah, R. (Universitas M. A. (2019). Analisis Penyebab Cacat Produk Menggunakan Metode Failure Mode and Effect Analysis ( FMEA ) pada PT. Sinar Sanata Electronic Industry. Tugas Akhir oleh : Risky Ardyansyah Fakultas Teknik Universitas Medan Area Medan. Universitas Medan Area, 243-257.
Arif Wicaksono, & Ferida Yuamita. (2022). Pengendalian Kualitas Produksi Sarden Mengunakan Metode Failure Mode and Effect Analysis (FMEA) dan Fault Tree Analysis (FTA) untuk Meminimalkan Cacat Kaleng di PT. XYZ. Jurnal Teknologi dan Manajemen Industri Terapan (JTMIT), 1(3), 145-154.
Banten Jaya Universitas. (2020). Pedoman Penyusunan / Penulisan Tugas Akhir / Skripsi. Pedoman Penyusunan Tugas Akhir Fakultas Teknik Universitas Banten Jaya.
Diana, Mayangsari Fitria, Hari, Adianto, & Yoana, Yuniati. (2015). Usulan Pengendalian Kualitas Produk Isolator dengan Metode Failure Mode and Effect Analysis (FMEA) dan Fault Tree Analysis (FTA). Teknik Industri Nasional Bandung, 3(2), 81-91, https://doi.org/10.35261skaov6i1.48786.
Elyas, R., & Handayani, W. (2020). Statistical Process Control (SPC) untuk Pengendalian Kualitas Produk Mebel di UD. Ihtiar Jaya. Bisma: Jurnal Manajemen, 6(1), 50. https://doi.org/10.23887/bjm.v6i1.24415.
Haryanto, E. (2019). Analisis Pengendalian Kualitas Produk Bos Rotor pada Proses Mesin CNC Lathe dengan Metode Seven Tools. Jurnal Teknik, 8(1). https://doi.org/10.31000/jt.v8i1.1595.
Hisprastin, Y., & Musfiroh, I. (2020). Ishikawa Diagram dan Failure Mode Effect Analysis (FMEA) sebagai Metode yang Sering Digunakan dalam Manajemen Risiko Mutu di Industri. Majalah Farmasetika, 6(1), 1. https://doi.org/10.24198/mfarmasetika.v6i1.27106.
Hoiriyah, Y. U. (2019). Peningkatan Kualitas Produksi Garam Menggunakan Teknologi Geomembran. Jurnal Studi Manajemen dan Bisnis, 6(2), 71-76. https://doi.org/10.21107/jsmb.v6i2.6684.
Kasad, F. (2018). Analisa Pengendalian Kualitas Produk Versaboard di PT. Bakrie Building Industries Menggunakan Metode FTA dan FMEA. Universitas Mercu Buana, https://doi.org/9.8473/fkef.92748
Krisnaningsih, E., & Hadi, F. (2020). Strategi Mengurangi Produk Cacat pada Pengecatan Boiler Steel Structure dengan Metode Six Sigma di PT. Cigading Habeam Center. Jurnal InTent: Jurnal Industri dan Teknologi Terpadu, 3(1), 11-24. http://ejournal.lppm-unbaja.ac.id/index.php/intent/article/view/796.
Nender, M., Manossoh, H., & Tangkuman, S. J. (2021). Analisis Perlakuan Akuntansi Produk Rusak dan Produk Cacat dalam Perhitungan Biaya Produksi untuk Menentukkan Harga Jual pada UD. 7 Jaya Meubel Tondano. Jurnal EMBA, 9(2), 441-448. https://ejournal.unsrat.ac.id/index.php/emba/article/view/33485/31688.
Prakoso, S., & Putra, Y. A. (2020). Pengendalian Kualitas Twisted Cable dengan Metode Seven Tools dan Quality Control Circle ( QCC ) di PT. Voksel Electric Tbk. Jupiter: Journal of Computer & Information, 1(2), 89-108, https://doi.org/10.35261/bv6sksi1.4516
Saputra, R., & Santoso, D. T. (2021). Analisis Kegagalan Proses Produksi Plastik pada Mesin Cutting di PT. FKP dengan Pendekatan Failure Mode and Effect Analysis dan Diagram Pareto. Barometer, 6(1), 322-327. https://doi.org/10.35261/barometer.v6i1.4516.
Setiawan, E., Orgianus, Y., & Mulyati, D. S. (2018). Penerapan Pengendalian Kualitas Menggunakan Metode Fault Tree Analysis (FTA) dan Failure Mode and Effects Analysis (FMEA) untuk Meminimasi Cacat pada Produk Sweater (Studi Kasus: Home Industry Era Baru Q95). Prosiding Teknik Industri ISSN: 2460-6502, 4(1), 127-134.
Sihombing, M. I. S., & Sumartini, S. (2017). Pengaruh Pengendalian Kualitas Bahan Baku dan Pengendalian Kualitas Proses Produksi terhadap Kuantitas Produk Cacat dan Dampaknya pada Biaya Kualitas (Cost of Quality). Jurnal Ilmu Manajemen dan Bisnis, 8(2), 42. https://doi.org/10.17509/jimb.v8i2.12665.
Sugiri, Dina. (2020). Analisis Kinerja PT. Bank Pembangunan Daerah Sumatera Selatan dan Bangka Belitung. Jurnal Manajemen dan Bisnis, 9(1), 82-88. https://doi.org/10.53812/jmb.v9i1.13.
